Suppliers of steel products.

4130 steel hardness hrc

Leave a comment

4130 Modified - BICO Steel Service Centers

4130 Modified Prehardened/Through Hardened 290/320 HB (30/34 HRC) ® Industeel Trademark C.25 Cr 1.30 Mn 1.30 Mo 0.4 Chemical Analysis - % Weight Other Element B NOTE:Typical values for a plate 100 mm (4 thick). Mechanical Properties Hardness (HB) 305 Y.S. 0.2 MPa (KSI) 920 (134) UTS MPa (KSI) 1250 (148) El 5.65 % 13.5 Young Modulus GPa 205 4130 and 4140 Heat Treatments - Industrial HeatingJun 08, 2011 · 4130 is a medium-carbon (nominal 0.30%C) chromium-molybdenum alloy steel. Due to its carbon content, it is most often water quenched to attain a maximum as-quenched hardness of approximately 48 HRC.

4130HW Alloy Steel - TimkenSteel

TimkenSteels 4130HW steel is a fine-grained, low-alloy steel that offers optimum heat-treat response in heavier . cross-sections. It is used in a variety of bar and tubing applications in quenched/tempered conditions. Yield strengths range from 80 ksi through 95 ksi 4140 Pre Hard - BICO Steel Service CentersHardness YS 0.2 HB MPa KSI MPa KSI % Z% GPa KSI Typical values for plates air quenched and tempered (thickness 45mm - 1.8) Transverse direction UTS El Reduction of area modulus Elastic 2312 (311-345 HB / 33-37 HRC) with improved machinability CCT Diagram ® Industeel Trademark AISI 4130 Alloy Steel Royal-AISI 4130 steel stockholders and suppliers, delivering to the whole of the UK. AISI 4130 is a chromium molybdenum alloy steel specification. It is supplied as round bar commonly in the hardened and tempered condition with a hardness of 18-22 HRc.

AISI 4130 Alloy Steel (UNS G41300) - AZoM

Sep 06, 2012 · AISI 4130 steel can be annealed at 843°C (1550°F) followed by air cooling at 482°C (900°F). Tempering of AISI 4130 steel can be performed at 399 to 566°C (750 to 1050°F), depending on the desired strength level. Hardening of AISI 4130 steel can be AISI 4130 Alloy Steel - West Yorkshire SteelAISI 4130 is a chromium molybdenum alloy steel specification. It is supplied as round bar commonly in the hardened and tempered condition with a hardness of 18-22 HRc. With a lower carbon content range AISI 4130 provides better weldability, at the expense of through thickness strength, than that of other oil and gas steel grades such as AISI 4140. AISI 4130 MODIFIED / UNS G41300 - Sverdrup SteelAISI 4130 is a low alloyed hardened and tempered steel used for Oil and gas drilling and production equipment wellhead and Christmas tree equipment.

AISI 4130 Steel, normalized at 870°C (1600°F)

AISI 4130 Steel, normalized at 870°C (1600°F) Medium Carbon Steel. Material Notes:A very common general purpose grade of medium carbon, Cr-Mo steel. Flexibility afforded by heat treatment options allows it to attain a range of toughness and strength values. Converted from Brinell hardness. Value below normal HRC range, for comparison AISI 4130 Steel, water quenched 855°C (1570°F), 595°C AISI 4130 Steel, water quenched 855°C (1570°F), 595°C (1100°F) temper, 100 mm (4 in.) round As quenched hardness:45.5 HRC surface, 25 HRC 1/2 radius, 24.5 HRC center Typical for steel; Bulk Modulus, Typical for steel; Poissons Ratio, Calculated; Machinability, annealed and cold drawn. Based on 100% machinability for AISI 1212 steel. AISI 4150 Alloy Steel (UNS G41500) - AZoMHardness, Rockwell C (converted from Brinell hardness. Value below normal HRC range, for comparison purposes only) 13:13: AISI 4150 alloy steel is tempered at 205 to 649°C (400 to 1200°F) based on the desired hardness level. The hardness of this steel can be reduced if the tempering temperature is higher. Hardening.

DME STEEL PLATES DME-NO.2 AISI 4130

Applications. DME No.2 Steel is an AISI 4130 type holder block steel is supplied pre-heat treated to 28-34 HRC (271-321 Bhn). A high-strength steel, DME No. 2 is ideal for cavity and core retainer plates, clamping plates, and support plates in molds and dies. DME STEEL PLATES DME-NO.2 AISI 4130DME-NO.2 AISI 4130 Applications DME No.2 Steel is an AISI 4130 type holder block steel is supplied pre-heat treated to 28-34 HRC (271-321 Bhn). A high-strength steel, DME No. 2 is ideal for cavity and core retainer plates, clamping plates, and support plates in molds and dies. Various application for this versatile steel formulation include but Differences Between Normalized and Annealed 4130 Steel This process occurs in steel when it is worked, machined or heated. When 4130 is heated and held at 1,525 degrees, the crystalline structure of the steel begins to revert back to a malleable state. Fully annealed 4130 has a tensile strength of 81,200 pounds per square inch and a Rockwell hardness of 95.

Hardened and Hardenable Metals Suitable for Making Armour

Nov 05, 2017 · The density of 4130 alloy steel is 7.85 g/cc / 0.284 lb/in³ so it is 1.775 times heavier per volume. If you multiple the 1.775 by the 128ksi yield strength to get a idea of the strength to weight relative to 4130 alloy steel it is 227ksi / 1565MPa, which is 9% more than the 208ksi / 1434MPa. The elongation before break is 14%. SAE AISI 4140 Steel Properties, Material Heat Treatment SAE AISI 4140 Alloy Steel. SAE 4140 (AISI 4140 steel) is a Cr-Mo series (Chrome molybdenum series) low alloy steel, this material has high strength and hardenability, good toughness, small deformation during quenching, high creep strength and long-lasting strength at high temperature. 4140 Steel Uses. AISI SAE 4140 alloy steel can be made into round steel bar, flat & square steel bar, steel Wingate Alloys Inc.4140 Chromium-Molybdenum Steel. Supplied in the annealed or prehardened condition. 4140 PREHARD is heat treated to a medium hardness (HRC 28/32) and is designated as 4140 HT. 4140 annealed is supplied in the soft condition and can be hardened to RC 40.

4130 Steel Bar - 4130 Alloy Steel Alternative

Hardness, Rockwell B (Converted from Brinell hardness) 95:95:Hardness, Rockwell C (Converted from Brinell hardness, value below normal HRC range, for comparison purposes only.) 17:17:Hardness, Vickers (Converted from Brinell hardness) 228:228:Machinability (Annealed and cold drawn. Based on 100% machinability for AISI 1212 steel.) 70:70